Papers

This paper presents a learning-based adaptive augmentation control concept inspired by the adaptation mechanisms of conventional adaptive control, while not being restricted to their specific parametric adaptation structures. In contrast to augmenting a reinforcement learning (RL) baseline controller with classical adaptive control to account for the simulation-to-reality gap, the proposed approach uses RL-based adaptive augmentation to address the limitations of conventional adaptive control. Domain randomization combined with observation stacking is employed to train the RL-based augmentation to compensate for matched uncertainties in a fixed-wing aircraft system. To ensure constraint satisfaction during operation, a safety filter is incorporated into the control architecture. Based on the concept of pseudo control hedging (PCH), we propose a modified reference model that avoids undesirable interactions between the RL-based augmentation and the safety filter. To reduce the conservatism of the safety filter, we additionally incorporate a disturbance observer. The proposed approach is evaluated on a fixed-wing aircraft model subject to uncertainties.

Low-voltage (LV) distribution feeders are increasingly difficult to monitor because real-time load data are unavailable, historical measurements are sparsely sampled, and high-rate voltage sensors cover only a few nodes. This paper proposes a multi-stage linear programming (MSLP) estimator for three-phase unbalanced LV grids that reconstructs per-phase nodal voltages under such limited observability. The estimator linearises the three-phase power flow through voltage-to-power sensitivity matrices and adjusts the nodal active and reactive power injections so that the resulting voltages match the available measurements. To limit the error introduced by linearisation, the sensitivities are rebuilt and the power corrections refined over successive iterations, and power-balance constraints at intermediate metered nodes are added to tighten the feasible region. The method is validated on a real 50-node Danish LV feeder, where it attains a mean absolute error of 0.641V, a standard deviation of 0.816V, a root-mean-square error of 0.842~V, and a maximum error of 3.437V. Compared with a single-stage linear estimator, MSLP lowers the error metrics by roughly 16 percent on average, and additional studies quantify the influence of the input-preparation strategy and of the number of estimation meters.

Parameter mismatch is the main source of rotor position estimation error in sensorless control of surface-permanent magnet synchronous motors (SPMSMs). To this end, this paper proposes a simple yet efficient equivalent flux compensation (EFC) method that directly estimates the equivalent flux disturbance caused by parameter mismatches in real time. First, the equivalent flux disturbance caused by parameter mismatches is derived from a nonlinear flux observer. Second, a flux update law is proposed to minimize both magnitude and directional errors by leveraging geometric error together with the derived equivalent flux disturbance. To enhance numerical stability, a saturation function is introduced to improve gradient continuity in the update process. Additionally, Lyapunov analysis is employed to ensure the stability of the proposed update law, from which the corresponding error bounds and convergence properties are derived. Finally, experimental results validate that the proposed method fully compensates for the steady-state effects of resistance and flux mismatches, and partially mitigates the influence of inductance variation, effectively constraining the position estimation error within a relatively small range.

To address the widespread sensitivity of surface-mounted permanent magnet synchronous motor (SPMSM) sensorless control to motor parameters, this paper proposes a temporal regression-based model-free sensorless control (TFC) method. First, voltage integrals and current increments over consecutive short intervals are stacked to construct a finite window regression, in which the unknown stator inductance appears as a common scalar coefficient. Second, a projection operator constructed from the stacked current increments eliminates the inductance term, and a least-squares formulation is developed to reconstruct the rotor flux vector. Meanwhile, the analysis of the projected regression and current-flux geometry establishes a two-dimensional direction vector whose components share a common amplitude containing the stator resistance and flux linkage. This amplitude cancels during position extraction. By setting the resistance reference to zero, the proposed method estimates the position without specifying the stator resistance, inductance, or flux linkage. Finally, experimental results verify the effectiveness of the proposed TFC method.

Iterative model-based reconstruction in photoacoustic tomography repeatedly applies the forward operator mapping the initial pressure to the transducer signals, and its adjoint. At the scale of current three-dimensional systems, this operator cannot be stored and must be evaluated matrix-free, while accounting for the finite, focused surface of the transducers, whose spatial impulse response degrades the resolution when ignored. Representing the initial pressure by compactly supported radial functions, we show that the measured signal is exactly a temporal convolution between a system kernel gathering the radial function and the electrical impulse response, and a purely geometric quantity accounting for the portion of the transducer surface reached by the wave emitted from a voxel during one time step. Two implementations are proposed, differing only in how this quantity is evaluated: a quadrature over points of the surface, as in existing works, or a closed-form area, which never discretizes the surface. We derive closed forms for planar and cylindrically focused transducers and provide, in the latter case, two accelerations of the resulting elliptic integrals, a lookup table and a trapezoidal approximation, together with the piecewise planar approximation customary in the literature. These implementations reduce the per-voxel geometric computations and are released as an open-source Python package for graphics processing units. The performance of these operators is first demonstrated on a synthetic phantom, where the lookup-table-based operator reaches the accuracy of the exact evaluation ten times faster and outperforms the point discretization on both accuracy and runtime. A second experiment shows that they enable the processing of a realistic vascular phantom at full scale, with a higher peak signalto-noise ratio and a better resolution than the back-projection counterpart. The released implementations are an important step towards the adoption of three-dimensional modelbased photoacoustic reconstructions with finite and focused transducers.

Target speech extraction (TSE) typically trains a separate extractor per cue, and visual-cue systems often need corruption-matched training to remain robust under visual frame corruption. We show that one autoregressive LLM backbone, TSE-Omni, can serve both temporally synchronous cues (lip movements, co-speech gestures) and asynchronous cues (enrollment audio, text). TSE-Omni is driven by next-token prediction: each step predicts target speech semantic tokens from its own past outputs, which we term self-enrollment, forming a continuous target-speech context initialized by the enrollment cue (asynchronous audio or text, or a short visual prefix). This enables audio-visual compensation: the model uses synchronized visuals when intact and its token history when visual frames are missing. Under clean visuals, TSE-Omni matches strong discriminative and generative baselines (SpeechBERTScore 0.81 on VoxCeleb2 and 0.89 on LRS3 zero-shot) with higher DNSMOS. On the same VoxCeleb2 test set, after a 2 s clean visual start, removing the remaining visual frames leaves SpeechBERTScore at 0.81. It remains usable under sparse overlap and multi-speaker interference, and supports streaming inference. Project page: https://alexwxwu.github.io/tseomni-main/.

The fidelity of image reconstruction from projections in linear inverse problems, such as tomography, is critically dependent on the synergistic interaction between frequency-domain filtering and spatial-domain interpolation. However, a physical model that can quantitatively describe how these two components cascade interact in the frequency domain and ultimately determine image quality is still lacking to this day. Here, we introduce a unified frequency-domain model that conceptualizes the combined effect of filtering and interpolation in the filtered backprojection (FBP) algorithm as a cascaded modulation process. This model demonstrates that the effective reconstruction spectrum is determined by the original projection data being sequentially modulated by the frequency responses of the filter and the interpolation kernel. Comprehensive numerical simulations and synchrotron radiation CT experiments validate the model, confirming its power to explain the performance hierarchy of classical filter-interpolation pairs under both ideal and noisy conditions. The model successfully predicts key performance characteristics, including spatial resolution and structural fidelity, thereby elucidating the physical principles behind the efficacy of specific combinations. This work establishes a generalizable theoretical foundation for analyzing cascaded systems in linear inverse problems, moving the practice of algorithm selection in computational imaging from empiricism to a principled, physics-based paradigm.

Speaker distance estimators are trained almost exclusively on simulated room acoustics, because real recordings annotated with the true talker-to-microphone distance are scarce. We show that models trained this way transfer poorly. On three real corpora we evaluate, simply predicting the average distance of the corpus is more accurate than any learned model. Then, we ask how few labelled real utterances are needed to make a frozen, synthetic-trained estimator useful, and study post-hoc calibration maps that rescale its output without gradients or retraining. An analysis of the achievable error shows that what the calibration is not limited by the absolute accuracy of the estimator, but how well it orders utterances by distance, since a constant bias or a wrong output scale is removed exactly by the calibration itself. Balancing this against the cost of estimating each coefficient from few samples yields a criterion that accounts for which map wins on which corpus and at which annotation budget, together with a shrinkage variant that requires no hard decision. Our findings suggest selecting synthetic checkpoints by linear correlation with true distances rather than by absolute error. Code, datasets, and analysis are available at https://github.com/michaelneri/audio-distance-estimation.

Coordinate-based overfitting image codecs have attracted increasing attention for their low decoding complexity and independence from cross-image generalization. However, representative approaches such as COOL-CHIC face an inherent entropy-modeling trade-off: lightweight models have limited capacity, while more expressive ones incur additional bitrate overhead from transmitting image-specific parameters. Inspired by the prediction mechanism in traditional codecs, we propose a new entropy-modeling strategy that introduces complementary prediction modes with region-adaptive soft mode selection, rather than relying on a single learned predictor to model diverse types of redundancy. Based on this concept, we develop a Long-Range Context Extrapolation Enhanced Entropy Model (LC3EM), which can be integrated into coordinate-based overfitting codecs. Specifically, a parameter-free Neighborhood-based Linear Extrapolation Mode (NLEM) complements the tiny MLP-based local predictor to exploit long-range contextual redundancy and strongly directional structures. A Minimum-Entropy-Inspired Continuous Mode Selection strategy is designed to adaptively fuse these two complementary modes, while requiring the transmission of only the parameters of a single additional linear layer. Moreover, to alleviate the mismatch between training-time relaxed and actual discrete quantization, we introduce a lightweight iterative latent rounding refinement stage to improve compression performance. Experiments demonstrate consistent improvements across diverse benchmarks, particularly on highly regular computer-generated images. When integrated with COOL-CHIC 4.0, the proposed method achieves BD-rate gains of -3.43% and -7.69% on the SIQAD and API datasets, respectively. With COOL-CHIC 5.0 as the backbone, the corresponding gains are -2.88% and -3.15%, respectively. The code will be made publicly available soon.

The 3GPP 5G non-terrestrial networks (NTN) technology fundamentally relies on a global navigation satellite system (GNSS) fix at the user equipment (UE) to pre-compensate for user-link delay and Doppler shifts prior to any transmission, including the random-access procedure for initial access. In GNSS-denied or interfered environments, this dependency triggers preamble collisions and connection dropouts, undermining satellite-based global connectivity. To address this vulnerability, this paper introduces a novel single-satellite positioning framework designed for higher-frequency (Ku- or Ka-band) 5G NTN very small aperture terminals (VSATs) equipped with a phased-array antenna. The multi-step scheme derives an initial coarse position from angle of arrival (AoA) observables, extracts frequency of arrival (FoA) and time of arrival (ToA) measurements from low Earth orbit (LEO) downlink reference signals, and hybridizes them within a Levenberg-Marquardt navigation filter. Systematic evaluations across static grids and realistic dynamic urban trajectories detail the incremental gains of transitioning from single-epoch AoA error minimization to multi-epoch angular tracking, followed by the integration of Doppler and ranging observables. Grounded in a realistic error budget, the proposed framework reduces initial positioning uncertainty from tens of kilometres down to a few kilometres. This level of positioning accuracy, combined with the GNSS-resilient features introduced in 3GPP Release 20 NR NTN specifications, enables robust initial access in compromised operational environments with minimal relaxation of 3GPP standards.

Frozen self-supervised (SSL) speech encoders are strong, low-cost front ends for audio deepfake detection, and recent comparisons agree that large, multilingual, discriminative encoders generalize best out of domain. These comparisons fail to control for encoder capacity, pretraining objective, and multilingual coverage together, identifying which encoder wins without isolating why. We present a controlled decomposition with a fixed pipeline and trainable capacity. We vary multilingual coverage on four wav2vec2-family encoders, matched to ~315M parameters. We isolate the pretraining objective on two encoders matched on identical data. Coverage does not help monotonically, as out-of-domain error drops sharply at the ~100-language scale (XLS-R) but does not improve further at the 1406-language extreme (MMS). We find that a mid-coverage encoder is strongest on farther out-of-domain sets, matching or surpassing a 577M-parameter model at 315M. Its lead on these far sets, statistically significant under paired bootstrap, and on the official ASVspoof 5 cost metric holds under two backends. Separately, masked-prediction pretraining generalizes better than contrastive on identical data (In-the-Wild EER 26.5% vs. 46.8%). Within this fixed frozen-encoder recipe, we find that broader and larger models are not reliably better.

We propose a bio-inspired approach that uses the inner-hair-cell (IHC) response of the Cascade of Asymmetric Resonators with Fast-Acting Compression (CARFAC) model to efficiently extract cyclic modulation from acoustic signals. We further investigate the contribution of IHC processing by comparing the CARFAC-IHC response with the CARFAC basilar-membrane (BM) filtering. Furthermore, the CARFAC-IHC and CARFAC-BM approach are benchmarked against conventional FFT Accumulation Method (FAM), Integrated Cyclic Modulation Coherence (ICMC), and Detection of Envelope Modulation On Noise (DEMON) approaches using the Case Western Reserve University (CWRU) bearing dataset and a real ShipsEar work-vessel recording dataset. The results demonstrate reliable recovery of characteristic cyclic components while substantially reducing the computational burden of conventional cyclostationary analysis.

In cross-lingual zero-shot text-to-speech, the accent of the reference leaks into the target speech. We propose accent analogy guidance (AAG), a training-free sampler term that subtracts an accent direction estimated from the model's own predictions for one synthetic voice rendered in both languages, so the voice cancels and only the accent remains. By a blind LLM accent judge on real dubbing data, reweighting classifier-free guidance between reference and text, and its variants, stay near one identity-accent trade-off curve; we score a method by its speaker similarity above that curve at equal accent ($\Delta$SIM). Across four open TTS models AAG lies above the curve: on OmniVoice $\Delta$SIM is +0.11 to +0.27 on three test sets (accent 3.51 to 4.28 on a 1-5 scale at speaker similarity 0.29, where reweighting keeps 0.02); MaskGCT and CosyVoice 2 also lie above their curves, and on F5-TTS it is more native than any reweighting setting. An LLM-free language-ID measure and a twelve-listener panel agree. A premise test and the reach of a model's own curve indicate in advance whether and roughly how much AAG can gain, predicting the one model where it gains nothing (X-Voice).

The constant-Q transform (CQT) represents audio on a logarithmic frequency axis. Its nonstationary Gabor formulation is exactly invertible, but the unequal numbers of time coefficients in its bands complicate GPU computation. An exact factorisation combines spectral selection, conjugation, windowing, and reordering into a fixed map between one packed Fourier transform and the shorter band inverse transforms. The factors give waveform reconstruction, real adjoints for backpropagation, and bounds on arithmetic depth and block width; overlapping slices permit streaming with bounded memory. Tests on two GPU models show that Flash-CQT reduces analysis-synthesis round-trip time by factors of two to eight relative to a baseline computing the same CQT. The proposed implementation also uses over 30% less peak temporary workspace and reaches a negligible reconstruction error, with a signal-to-noise ratio of about 130 dB, in single-precision floating-point arithmetic. These advances make Flash-CQT a practical, computationally efficient front end for spectral analysis and modern audio machine-learning systems.

Industrial robots are rarely used for machining tasks due to their limited path accuracy. This accuracy is mainly limited by inaccuracies in the drive trains. Compliance and transmission errors occur in the joint gearboxes. While transmission errors have been extensively studied for strain wave gears, there is little research on these errors in cycloidal drives. This gearbox type is commonly used in industrial robots for medium to heavy payloads. It is proposed to model the mainly periodic transmission errors using a Fourier series where amplitude and phase are defined as a polynomial function of the main influence factors load-torque, velocity, and temperature. Measurements of the transmission errors were conducted using an experimental setup representing a single robot joint. In the evaluation of the measurement data, harmonic frequencies were related to mechanical properties of the cycloidal drive. These frequencies were used to identify the parameters of the polynomial Fourier series model. Compared to validation measurements, the derived model shows an average root mean square error of 0.026 mrad. It is proposed to use the output of the resulting model in a feedforward control approach to compensate the transmission errors and to increase the path accuracy of industrial robots.

European electricity trading in the EU operates as a constrained multi-layer system in which legal design, exchange microstructure, and network physics are executed jointly across forward, day-ahead, intraday, and balancing horizons. This paper develops a functional architecture for AI-supported trading that is aligned with market-coupling mechanics, cross-zonal transfer constraints, and compliance obligations under REMIT, MiFID II, MiFIR, and EMIR. The contribution is a formal system specification composed of a decision-state vector, residual-exposure accounting, constrained optimization objective, executable-action permission gate, and fail-closed AI control logic with auditable records. The analysis maps major Nominated Electricity Market Operator (NEMO) venues and related exchange operators into an operational venue topology and identifies where cross-border coordination fails in practice: interface-level timing, permission heterogeneity, and balancing-layer coupling. The resulting framework proposes how AI can be deployed as a bounded decision component inside regulated market operation with explicit governance, rather than as an unconstrained prediction layer.

This paper investigates model predictive control (MPC) for switched systems subject to control and state constraints. A variable-horizon switched MPC approach is proposed. By steering the system state into a well-designed switching feasible set, the proposed method structurally decouples the dwell-time conditions from the MPC constraints, thereby relaxing the dwell-time requirements to match those of the unconstrained switched systems. Furthermore, algorithms are developed to construct this switching feasible set and characterize the domain of attraction, ensuring both persistent feasibility and closed-loop asymptotic stability. To further decouple the prediction horizon length from strict dwell-time bounds, advanced short-horizon switched MPC schemes are designed, which expand the overall domain of attraction. Simulations illustrate the efficacy of the proposed methods.

Variational quantum algorithm is a leading approach for quantum chemistry and many-body physics on noisy intermediate-scale quantum devices. The performance depends strongly on the structure of the parameterized quantum circuits. Quantum architecture search (QAS) can automate ansatz design. However, it requires repeated training and evaluation of many candidate circuits, leading to high evaluation cost. In this work, we propose a noise-aware quantum architecture search framework based on ZX-calculus topological reuse (ZX-QAS). The framework encodes the search space with a ternary Gray-code mapping and integrates a noise-aware quantum neural network with a ZX-calculus topological reuse mechanism. The effectiveness of the framework is validated through ground-state energy estimation tasks and one-dimensional transverse-field Ising model tasks under noisy conditions. The results show that the ZX-QAS exhibits stable convergence and remarkably reduces the cost of expensive evaluations under noisy conditions.

Low-pass (LP) filtering is a fundamental operation in graph signal processing (GSP). Among finite-order nodal-domain methods, Lanczos-based filtering provides more accurate approximations of ideal LP filters than Chebyshev polynomial methods. We show that the approximation of Lanczos filtering can be further improved through algorithm unrolling and data-driven parameter learning. The key insight is that, because ideal LP filtering is a projection operation into the low-frequency eigen-subspace $\cS_K$, instead of approximating individual eigen-pairs of a graph Laplacian $\L$ as done in classical Lanczos, an unrolled Lanczos network can directly approximate $\cS_K$. Specifically, we first establish a theorem identifying properties of the Lanczos tridiagonal matrix $\T_m$ that promote accurate approximation of the low-frequency eigen-subspace $\cS_K$. Guided by this theory, we relax the orthogonality constraint on Lanczos vectors, resulting in Ritz vectors that better span $\cS_K$. To ensure numerical stability, we constrain $\T_m$ to be similar to a symmetric matrix, thereby guaranteeing real-valued eigenvalues. Experimental results on random graphs and learned graphs in two natural language processing (NLP) tasks show that our unrolled Lanczos network achieves superior ideal LP filter approximation compared to the classical Lanczos method.

This paper investigates communication-free bearing-only formation tracking control for multi-agent systems governed by Euler-Lagrange dynamics. Distinct from existing results that can only stabilize a stationary formation, this work considers a scenario where the leaders move with time-varying velocities while the inter-agent communication is absent. In this setup, the leaders' states (position and velocity) are unavailable to all followers and cannot be estimated via distributed observers. A novel adaptive distributed control scheme is developed to address this problem. The design exploits the fact that bearing rates contain the projected relative-velocity information, which, together with bearing rigidity, provides a rigidity-based damping mechanism for compensating the unavailable velocity error. Moreover, this damping mechanism is incorporated into a bearing-driven auxiliary variable to construct a surrogate velocity error, facilitating the adaptive control design for EL dynamics. Furthermore, since this damping mechanism necessitates sufficient bearing rigidity, we characterize a rigidity-preserving set and establish its forward invariance, thereby guaranteeing such rigidity via initial conditions. Via a Filippov-based Lyapunov analysis, the proposed scheme is shown to achieve local practical formation tracking in the sense that the velocity error converges to zero and the position error is uniformly ultimately bounded. As a corollary, for the constant-velocity case, asymptotic tracking is achieved without initial-condition restriction. The simulation results verify the effectiveness of the proposed control law.

Pilot-aided channel estimation is a decisive block in orthogonal frequency-division multiplexing (OFDM) receivers for both 5G New Radio (5G-NR) and Long-Term Evolution (LTE). A large body of estimators exists, from simple least-squares (LS) interpolation to statistically optimal linear minimum-mean-square-error (LMMSE) variants and, more recently, deep convolutional denoisers, yet no single estimator is uniformly best: the winner depends on the propagation scenario, the numerology, the operating signal-to-noise ratio (SNR), the mobility (Doppler), and the antenna configuration. In this paper, we quantify this fact through a unified study of eight literature estimators evaluated over the 3GPP TR~38.901 Urban-Macro (UMa), Urban-Micro (UMi), and Rural-Macro (RMa) channels generated with NVIDIA Sionna, for both 5G-NR and LTE numerologies, in single-input single-output (SISO) and $8\times2$ multiple-input multiple-output (MIMO) settings. We then propose a condition-adaptive multi-agent orchestrator that treats each estimator as an independent agent and dispatches, per operating condition, to the agent that is best on a validation split without any genie knowledge. The orchestrator tracks the per-realization oracle to within $1.07$~dB and improves the normalized mean-square error (NMSE) over the best fixed strategy by up to $3.6$~dB at high SNR, where the low-SNR champion is no longer optimal. Because the agents are independent, running them concurrently delivers this best-of-eight accuracy at essentially single-estimator latency: a data-parallel partition scales the wall-clock nearly as $1/K$ with $K$ workers (up to $6.9\times$), whereas naive by-algorithm partitioning is Amdahl-limited by the heaviest agent. The results substantiate multi-agent orchestration as a practical route to robust channel estimation across heterogeneous 5G-NR/LTE deployments.

We present a personalized Korean visual speech recognition (VSR) system and quantify, on the nine-camera OLKAVS corpus, the gap between the population-level benchmark score and an individual user's error. A video-only Conformer initialized from English-trained weights attains 9.95 - 12.19% character error rate (CER) under the corpus protocol against the published 26.64, and 19.00 - 21.52 on unseen wording. Per speaker, CER spans 1.0 to 52.2%, with seen wording lowering CER by 7.0 - 9.0 points and professional delivery and spontaneous speech raising it by 8.5 - 10.5 and 12.7 points. A low-rank adapter with 4.6% of the parameters, trained on 4 to 29 minutes of the user's frontal video, lowers the CER of twelve high-error speakers by 2.13 to 3.58 points, transfers to every camera without loss, and keeps 85% of the full fine-tuning gain at 12% of its cost to other speakers. Cameras above the mouth plane add about six CER points as a constant offset that training on all views keeps small.

Cross-embodiment learning has shown that a single model, such as a vision-language-action (VLA) model, can learn state representations and manipulation skills that can be applied across heterogeneous robots to accomplish various tasks. We hypothesize that the same holds for safety enforcement. The reasoning required to satisfy a safety constraint, such as detecting an obstacle, recognizing that it should be avoided, and selecting a safe abstract action, is largely shared across robots. What differs across embodiments is how the abstract safe action is realized: morphology, kinematics, and dynamics determine which actions are safe and feasible. Consequently, the same action can be safe for one robot and unsafe for another. This is especially important for generalist manipulation policies that operate in a common end-effector action space without explicitly capturing how safety depends on the robot's morphology and kinematics. We propose embodiment-conditioned safety filtering, in which a Hamilton-Jacobi reachability-based value function and its corresponding safety-maximizing policy are shared across robots. Using a morphology-aware latent representation of the robot and its environment, we perform Hamilton-Jacobi reachability analysis directly in latent space so that the learned safety concepts can generalize across embodiments while remaining explicitly conditioned on each robot's morphology and kinematics. We evaluate our approach across five bimanual robot embodiments and five manipulation tasks with whole-body collision-avoidance constraints. Our results show that a single policy, jointly trained across five manipulation tasks and four embodiments, exhibits zero-shot generalization to a held-out embodiment, reducing the nominal policy's collision rate. They also show that training using more embodiments improves generalization.

Post-training quantization (PTQ) reduces the cost of on-device text-to-speech (TTS), but published evaluations cover one system or method. We evaluate PTQ across TTS architectures under one protocol with three core models, weight and activation ablations of eight more, and two held-out models quantized blind. Four-bit per-channel weights reduce UTMOS, a predicted mean opinion score, by 2.8 on Supertonic and 0.07 on Kokoro, and per-tensor scaling can cause severe degradation even at 8 bits. The same bit width yields different outcomes, because the sensitive component is model-specific and not reliably predicted from the model class. A staged ablation procedure identifies it, and per-layer GPTQ can restore it to within 0.1 UTMOS. Real int8 and int4 kernels reproduce the simulated ordering at hardware-dependent cost. On a Mac mini, a 4-bit weight kernel runs Supertonic at 0.60x the fp32 latency while int8 is slower, so each configuration requires validation on the target runtime.

Diffusion MRI microstructure mapping (MM) is conventionally solved voxel by voxel, ignoring the fact that tissue microstructure forms a spatially organized field. This isolation leaves each estimation problem ill-posed and nonconvex. We instead cast MM as a single global inverse problem, reconstructing the entire parameter field jointly from all measurements of a subject. An untrained neural representation supplies implicit spatial priors and eases the nonconvex optimization, requiring no training data, while coregistered T1-weighted anatomy contributes structural guidance that is freely available in standard protocols. On both synthetic and in-vivo data, our method compares favorably with established voxel-wise and learning-based baselines, suggesting global inversion is a promising alternative.

Outdoor robots require more than an accurate receiver and a path-tracking law: the navigation system must preserve geometric consistency from geographic waypoints to actuator commands, expose measurement validity and timing, and respond to invalid or stale state information. This work presents a ROS~2 navigation stack with interchangeable single-GNSS–IMU and dual-antenna-GNSS localization front ends. Both provide a common local East–North–Up state interface for pure pursuit, virtual-point cross-track PID, finite-horizon nonlinear model predictive control (NMPC), and a segment-dependent hybrid dispatcher. The architecture specifies coordinate conventions, datum initialization, asynchronous state construction, waypoint geometry, controller equations, quality gates, command arbitration, and watchdog behavior. Independent physical field runs collected during 2025 and 2026 grape-vineyard deployments support a balanced evaluation of 800 runs, with 100 runs for each of eight controller–localization combinations on an approximately 199.6-m route. The row-hybrid mode yields the lowest run-averaged post-acquisition mean absolute cross-track error (MAE) in the evaluated dataset: 0.00952~m with single GNSS+IMU and 0.00846~m with dual GNSS. These findings characterize deviations of the recorded positions from the reference route under the evaluated conditions. The open-source navigation software and deployment instructions are available in the https://github.com/YiyuanLinXX/PPBv2/tree/main/PPBv2_Navigation.

Frame refresh rate estimation is a fundamental step in identifying compromising harmonic frequencies in electromagnetic side-channel attacks. Methods based on discrete linear autocorrelation (DLA) are robust across different scenarios and require a computational complexity of $O(N\log N)$ for a signal containing $N$ samples. This work proposes reducing this complexity to $O(N)$ by exploiting prior knowledge of the target system's display resolution, as is available for certain models of the Brazilian electronic voting machine. Experiments using software-defined radios show that the proposed method preserves the accuracy of the conventional approach in the evaluated scenarios.

Concurrent long-range (LoRa) transmissions over the same time-frequency and spreading factor (SF) resources generally result in packet collisions, as the gateway cannot distinguish the overlapping signals from different end devices (EDs). This paper advocates a new fluid antenna multiple access (FAMA) framework for LoRa, referred to as lora-FAMA, to provide spatial opportunities for LoRa multiuser communications. In lora-FAMA, a gateway employs a single fluid antenna connected to only one radio-frequency (RF) chain, whose radiating element traverses the antenna aperture by sequentially visiting all candidate positions, i.e., fluid antenna `ports', within each symbol interval. The signal segments collected along the trajectory are compensated using the channel state information for the target ED. As a result, the desired signal is coherently accumulated, whereas the signals from other EDs experience unmatched channel variations and thus cannot be coherently combined. Applying the compensation separately to each active ED enables simultaneous multiuser transmission. We analyze the statistical performance of lora-FAMA under asynchronous transmissions and spatially correlated fading, as well as the large-aperture limiting case with independent and identically distributed fading. Numerical results show close agreement between the analytical and Monte Carlo results. It is revealed that, with a normalized aperture of $4\times4$ and $\mathrm{SF}=9$, a gateway can simultaneously serve more than $10$ EDs over the same frequency and SF resources while maintaining a symbol error rate below $10^{-4}$. These results demonstrate the potential of fluid antennas to enable LoRa multiple access without multiple RF chains.

We study the differential privacy (DP) of a graph shift operator (GSO) when an analyst observes the output of a graph filter. In particular, we study the setting in which the input signals to the graph filter are drawn from a differentially private distribution. Unlike approaches that perturb the GSO or the filter output, we use the randomness already present in the inputs to protect the GSO. This yields an equivalent level of privacy protection to that of the perturbation methods without adding noise, and thus a better privacy-utility trade-off. We provide an explicit characterization of the privacy loss and its certificate in terms of the zeros of the graph filter. In doing so, we show that the log-likelihood ratio between the releases of two adjacent topologies is governed by the distances from each zero to the graph frequencies of the two GSOs. Then, by uniformly bounding the log-likelihood ratio over the adjacent topologies, we obtain an explicit $(\varepsilon,\delta)$-DP guarantee for Gaussian inputs. We further show, via a Cramér–Rao bound, that the zero placement that limits the privacy loss also raises the floor on the adversary's reconstruction error. Finally, empirical validation is performed on a synthetic network of financial exposures, where the largest position a pair can conceal and the accuracy with which it can be sized are collinear across pairs. Both are set by the graph-frequency content of the pair, and the full network becomes recoverable only as the certified budget grows.

Heterogeneous robot teams distribute complementary capabilities across specialized agents, but their physical roles and capacities typically remain fixed throughout a mission. We present HARP, a Heterogeneous Aerial Robotic modules Platform in which independently deployable aerial robots physically reconfigure to compose their capabilities for field operations. HARP comprises sensor-equipped scouts, flydrive rover modules, and task-specific payload modules. Scouts map the environment and inform an energy-aware planner that jointly selects routes and air-ground mobility modes. Rover and payload modules fly independently across terrain that constrains ground travel, then autonomously assemble into a cooperative ground vehicle for energy-efficient payload transport. Motivated by environmental sampling in remote and difficult-to-traverse regions, we evaluate HARP through field experiments spanning sensing, planning, reconfiguration, airground mobility, payload transport, and task execution. We further conduct module-level deployment tests on the Greenland Ice Sheet toward future autonomous missions. HARP demonstrates how heterogeneous robot teams can adapt not only their actions, but also how their physical capabilities are composed during a mission.